Things that give you the sh1ts

[Dutchy]

thought so, little fkers are tougher than my mother in law...

[Mic]

Do you blame the taxi driver, I try and avoid going anywhere near Noarlunga too.

Would have been a decent fair, if he dosent want it then he must be doing better than most taxi drivers.

Agreed, my old man has been driving taxis for nigh on 25 years and he doesn't refuse any fare. He does get frustrated about the job when people want to go just down the road but he still takes them on principle as taxis should take people anywhere they want to go. I can't stress enough that taxi drivers that refuse fares should be reported to the Taxi Board.

Yep. The only way drivers can refuse is if you are abusive, severely intoxicated or if there is reason to believe you do not have the money to pay the fare.

[locky801]

S.A. cricketers being bashed in Victoria

[mighty_tiger_79]

Do you blame the taxi driver, I try and avoid going anywhere near Noarlunga too.

Would have been a decent fair, if he dosent want it then he must be doing better than most taxi drivers.

Agreed, my old man has been driving taxis for nigh on 25 years and he doesn't refuse any fare. He does get frustrated about the job when people want to go just down the road but he still takes them on principle as taxis should take people anywhere they want to go. I can't stress enough that taxi drivers that refuse fares should be reported to the Taxi Board.

Yep. The only way drivers can refuse is if you are abusive, severely intoxicated or if there is reason to believe you do not have the money to pay the fare.

well at 12:45pm last friday i wasnt any of the above

[smac]

Dynabolts....anyony know how to get them out of a wall?

Use pliers to grip the outside of the bolt cover and tap the bolt into the wall slightly. This should move the thicker part of the bolt out of the cover allowing you to slide the cover out of the wall. The bolt should then come out easily.

[Dutchy]

Dynabolts....anyony know how to get them out of a wall?

Use pliers to grip the outside of the bolt cover and tap the bolt into the wall slightly. This should move the thicker part of the bolt out of the cover allowing you to slide the cover out of the wall. The bolt should then come out easily.

cheers SMac will give it a go, I used them to put up a clothes line and one didnt take properly but of course wouldnt come back out, so I drilled another hole above it and whacked another in! but the first one is still there and gets int he way of the line swinging back down when it retracts....

[smac]

Dynabolts....anyony know how to get them out of a wall?

Use pliers to grip the outside of the bolt cover and tap the bolt into the wall slightly. This should move the thicker part of the bolt out of the cover allowing you to slide the cover out of the wall. The bolt should then come out easily.

cheers SMac will give it a go, I used them to put up a clothes line and one didnt take properly but of course wouldnt come back out, so I drilled another hole above it and whacked another in! but the first one is still there and gets int he way of the line swinging back down when it retracts....

That's the same job I was doing when I learned how to remove them!

[Dutchy]

Also learnt that its much much easier drilling into brick with a masonry drill bit than a normal one! unfortuantely after I had already drilled 4 holes

[Dutchy]

driving into town when school is back

but ont he bright side, RUndle Mall is back to being nice and quiet!

[Dirko]

Also learnt that its much much easier drilling into brick with a masonry drill bit than a normal one! unfortuantely after I had already drilled 4 holes

LMAO. Put up some towel racks in the bathroom. Thought ohh year brick, get the hammer drill going...cracked tile later...tile dude says use a masonry bit but have the drill on normal !! DOH !!

[smac]

Also learnt that its much much easier drilling into brick with a masonry drill bit than a normal one! unfortuantely after I had already drilled 4 holes

It's only a mistake if you do it again... Until then it's a learning experience!

My home is riddled with learning experiences...

[Strawb]

Studying to pass an exam. I am afraid i will fail or forget the answers but I seem to remember all of what I need to Know

[RustyCage]

Also learnt that its much much easier drilling into brick with a masonry drill bit than a normal one! unfortuantely after I had already drilled 4 holes

It's only a mistake if you do it again... Until then it's a learning experience!

My home is riddled with learning experiences...

Its not a mistake if you do it again, its just a reminder that it didn't work the first time either.

[locky801]

My new bosses

[Wedgie]

Buying 3 shirts from the same retailer with the XL fitting fine and the 2XL tops being too small.
WTF?

[redden whites]

Buying 3 shirts from the same retailer with the XL fitting fine and the 2XL tops being too small.
WTF?

I am with ya Wedgie........ Annual work clothing issue..97st shorts perfect fit,97st pants I cant breathe in.Same brand FFS

[Psyber]

Buying 3 shirts from the same retailer with the XL fitting fine and the 2XL tops being too small.
WTF?

I am with ya Wedgie........ Annual work clothing issue..97st shorts perfect fit,97st pants I cant breathe in.Same brand FFS

Machined bulk cutting equals much variation from top to bottom of fabric file due to stretching. Rapid sewing but starving 3rd world outworkers equals much variation too. I bought a pair of track pants once with one leg too long and the other too short.

[saintal]

My best 2 mates at work leaving for greener pastures.

[silicone skyline]

I am with ya Wedgie........ Annual work clothing issue..97st shorts perfect fit,97st pants I cant breathe in.Same brand FFS

You wouldn't happen to have really FAT calf muscles???

[scoob]

julia gillards voice